Since people use LED lighting to read as the car lights, the source of almost no fever, while driving the vehicle at any time have greatly reduced the incidents may occur, thus reducing the serious security risks. LED lights up the life of 50,000 to 100,000 hours, that is 5 to 10 years or more, during the life of vehicles in general can not replace.

LED lights can be directly converted into electric energy, fully able to meet the needs of environmental protection and energy conservation. That do not have the original start, rectifiers, power can be directly bright, durable power-saving high-brightness, to use as a brake lights lit fast. But an incandescent bulbs, only the power of 12% to 18% for the conversion of solar energy, and the remaining thermal energy into electric energy are distributed. Ordinary incandescent bulbs start of a longer time, usually in the 100-300 milliseconds, and the LED is only a few dozen start-up time nanosecond. Is essential for high-speed driving in the brake lights, so the time gap means the difference between 4-7 meters braking distance and improve the safety of motorists.

LED indicator to achieve their own hands, the need for tools: utility knives, scissors, File, the torch / solder, small screwdriver, hot melt gun / seals, thermal control, such as meter.

General manual mirrors the relatively simple structure, the electric motor more adjustments within less space, so as to manually adjust the mirror easier construction. Even the manual mirrors, inside the structure is not small, triangular Guding Zuo, from top to bottom frame, lenses, rotating bodies, etc., be done in the open, clean Oiling action. Depression is the back of the wearer in a black plastic plate fixed, when the demolition to be careful.

The market for sale of licences screws on the lights, because the screws will be combined with LED lights, a water-resistant features, used in the installation of mirrors above the best; LED size and brightness of a small but high literacy results will not be lost General traditional light bulbs. First in the mirrors the surface to find a suitable location, in the back of a pen marked bored. Install the best location near the outside so that a moving vehicle, on both sides of the vehicle can clear identification.

First a small branch of the screwdriver on the surface runs a Aodong and down repeatedly rotating drill, electric drill even if you will, LED circle of good size, choose the right bit, Wahao hole. Add to LED lights will Wahao the hole, but not more than mirrors on the surface (to prevent car hit a narrow roadway will be shedding); hole size freshman than LED little like, with the lights at the same time, the screws slightly Bai Zhi, Card to avoid mirrors inside the structure.

Licence screws LED lights cathode independent wires pulled out, but the negative electrode is connected with the screw body, it must be extended to wire; prepared about one metre of red / black wire of the 1, the negative electrode directly on the welding part to thread . Because wires must be pulled out after as the microscope, and then pulled the engine room lights line connecting the direction of group, the first welding parts of the thermal coating, which to avoid short-circuit also helped. The use of hot melt gun LED lights will be fixed in the back of mirrors, to determine the hot melt glue only after the removal of the cooling fixed; LED lights and holes between the best point also crowded into the hot melt glue, fill the gaps also prevent Water into the internal results. Fixed, the negative electrode wires are connected to follow the normal battery testing and observation of light from the side of the case, if the LED too will lead to reduction in the luminescence was covered, hot melt glue can be removed once again.

After the normal tests, to start with some of the agencies. First is the installation of the mirror back on board, the board by the interior contain the link, overloading plate at the bottom of the body-driven, this part is very easy to get stuck dirty things, we should remember that point on the clean-up and lubrication oil. Will be fixed glass panels of black plastic wipe clean, and put only 3 M-plastic, glass polished after the paste. Mirrors from top to bottom covered by the card Chun, screw fixation, first to lock screw, a good card after card Chun, then the lens into the box pressure. Rear-view mirror after a good combination, in accordance with the demolition program to be installed on the return. Rearview mirror at high speed easily lead to wind shear sound, it can cut some of the thin film of soft rubber, caught in the plane of the lock back, can reduce the noise generated.

Use of meter or route map, will light the direction of the MMH-identified, and the negative side of the LED is fixed in the nearest body to screw. The recommendations follow from the direction of wire lampholders after connect, because even after the circuit in question, can also be very easy to repair. After the wires from the under side through the adjustment as Bogan, along the A-wear into the bottom leaves plate; leaves board will have reserved the holes, wires from the hole Chuanchu and the old engine room along the direction of fixed wireline group好. Direction and the LED lights MMH-MMH end of the fixed welding wire, put on the thermal control after you're done. Follow the direction of lights around the converted, because the LED lights and turn signals connection, so after playing the direction of lights, mirrors on the LED lamps will be lit with!